What details should you pay attention to when using Metal Optic Splice Cabinet
Ark of metal fiber connector manufacturers products are now widely used by people, its use has brought people a lot of help, but in the use of it, we should pay attention to what details? Let us know the details below!
When we use it in, you need a lot of attention to details, its electrical installation board should be located above the N terminal board and PE line terminal board above, followed by the word for the installation, should be the correct installation, firm, also requires the center of the switch box and the vertical distance of the ground should be 1.4 to 1.4 m, if you are using mobile products, then you should make this product it switch box shall be installed on the solid, stable support, it is the center of the best distance between the ground 0.8-1.6 m, but also should pay attention to the area of it is close to the power supply, these are all we need to pay attention to details.
Through the introduction to above, I believe you should be have a certain understanding, when use it, only a special attention to the details, will be able to play its role, better use of it, giving full play to the advantages of its own particular use.
Metal fiber joint cabinet manufacturer of metal fiber connector tank plays an important role in our life, but in the process of using, is there any way to prevent it from its damaged phenomenon? Let us know the details below!
When in the process of use, you need to know that it is data on the parameters, this product is mainly constitute a low voltage according to the electrical wiring, in use process, especially at the time of shut down or half closed Metal Optic Splice Cabinet, will constitute a low voltage ark of metal fiber optic connectors, when it is in normal operation, you can depend on the manual operation, can also with manual or automatic switch or breaker circuit. In general, this product mainly includes the cabinet, support board, support rod and cabinet door, in the process of use, it needs to be protected.
Metal fiber joint cabinet manufacturer told us, choose a good product, it is very important, by the quality of the product it will directly affect the safety of this product it performance, let's specific look at!
Metal Optic Splice Cabinet in the process of using fiber optic connectors, can involve a lot of problems, especially in the safety and rationality of the above is very important, in order to seek better development effect, so when in the process of selection, you need to choose the high quality product, from safety and line layout of metal fiber connector ark better processing, finally can bring advantage is extremely obvious. Only in this way can dangerous situations be reduced.
The Metal Optic Splice Cabinet produced by the metal fiber joint cabinet plays an important role in the life, but in the process of use, it is easy to appear what faults? Today, we will give you a detailed explanation.
First because of the quality of the products caused by the fault, in the process of production, product quality closes nevertheless, so operation fails, shortly after the problem requires the manufacturer to solve, strengthen the supervision of production, control product quality, the second real caused by improper selection for electrical fault, mainly is the ac contactor capacity caused by the inappropriate choice, if it is different for circuits installed with capacity of contactor, is need to consider the imbalance of three phase load conditions. Only this ensures that the product is safe to use.
And influence of environment temperature on the low voltage apparatus, it is prone to failure, so in the process of use, require ambient air temperature does not exceed the limit of 40 ℃, ambient air temperature average no more than 35 ℃ for 24 h, the lower limit of ambient air temperature is not lower than 5 ℃ and 25 ℃.
Categories
Contact Us
Hangzhou Zhongrui Communication Co.,Ltd.
Address:NO.1 Xiyuan Rd, WestLake Science & Tech. Park, Hangzhou, China
Tel:+86-571-88955081
M/P:+86-13282009101
Web: www.hzzrfttx.com
E-mail:CNFTTX007@foxmail.com
Service Hotline
+86-571-88955081
What Details Should You Pay Attention To When Using Metal Optic Splice Cabinet
Hangzhou Zhongrui Communication Co.,Ltd | Updated: Jul 13, 2017
Previous: What Should The Optic Splice Cabinet Be Aware Of
Next: Discussion On The Development Of Plastic Optic Distribution Box
Related News
- Characteristics Of The Connector Box
- The Technical Parameter Of Splice
- Light Box Introduced
- General Structure Of The Light Box
- Characteristics Of Light Box
- Light Box Use Conditions
- Technology Of Light Box Parameters
- Light Box Function
- Light Box Installation Instructions
- Distribution Frame A Brief Introduction
- What Should The Optic Splice Cabinet Be Aware Of
- Why Does The Shell Of SMC Optic Distribution Box Leak
- According To The Use Of Stainless Steel FTTH Box To Deter...
- Optic Splice Cabinet Manufacturers Can Play A Great Role
- How To Operate The Metal Optic Splice Cabinet Safely
- FTTH Box And Switch Box Location Selection And Environmen...
- Installation And Use Of Optic Splice Cabinet
- Metal Optic Distribution Box For The Use Of Electricity M...
- Importance Of Metal Spray Connector On Metal Optic Splice...
- SMC Optic Distribution Box Installation Of The Basic Requ...